LayItLow.com Lowrider Forums banner

1 - 20 of 20 Posts

·
Registered
Joined
·
948 Posts
Discussion Starter #1
Is it possible 2 hardline the pressure side of the pump? from pump 2 cylinder..
Going 2 change some coils and start hoppin, no serious inches just bounceín..
What size tubes should i use? just tell me everything i should know bout it....
 

·
Registered
Joined
·
2,562 Posts
stainless 3/8 .049. or stainless 1/2 .068 :biggrin:
 

·
Registered
Joined
·
23,424 Posts
Originally posted by caranto@Aug 29 2005, 04:49 PM~3713905
stainless 3/8 .049. or stainless 1/2 .068 :biggrin:

What do you know besides everything. :biggrin:
 

·
Registered
Joined
·
3,417 Posts
Originally posted by caranto@Aug 29 2005, 01:49 PM~3713905
stainless 3/8 .049. or stainless 1/2 .068 :biggrin:
hey caranto is there a hand held bender that i can use on 1/2 in hardline?? stainless by the way
 

·
Registered
Joined
·
948 Posts
Discussion Starter #10
Can i use this, stainless 3/8 .049. or stainless 1/2 .068 .. for the pressure side? Going to go 60volts...
 

·
Registered
Joined
·
2,562 Posts
Originally posted by eyecandy1n2@Aug 30 2005, 07:39 AM~3718802
hey caranto is there a hand held bender that i can use on 1/2 in hardline?? stainless by the way
yes i got an imperial but parker sells a nicer one....hope you got some strong forearms... i had to put mine in a vise to bend some of "poision ivy's" lines....
 

·
Registered
Joined
·
2,562 Posts
Originally posted by thephatlander@Aug 30 2005, 09:16 AM~3719108
Can i use this, stainless 3/8 .049. or stainless 1/2 .068 .. for the pressure side? Going to go 60volts...
yes!!! u need to put aleast 3 foot of standard hose on the pressure side....like ron said.... or you can buy some stock in seals and gears......somethings gotta give! :biggrin:
 

·
Registered
Joined
·
23,424 Posts
Originally posted by caranto@Aug 30 2005, 01:58 PM~3719917
yes i got an imperial but parker sells a nicer one....hope you got some strong forearms... i had to put mine in a vise to bend some of "poision ivy's" lines....

Only because yours are smaller than the hardline itself. :biggrin:
 

·
Registered
Joined
·
2,562 Posts
:biggrin:
Originally posted by timdog57@Aug 30 2005, 01:20 PM~3720438
Only because yours are smaller than the hardline itself.  :biggrin:
:biggrin: leave us little people alone mr. buff!!!! :biggrin: dont you have some weights to lift :biggrin:
 

·
Registered
Joined
·
23,424 Posts
Originally posted by caranto@Aug 30 2005, 04:21 PM~3720761
:biggrin:
:biggrin:  leave us little people alone mr. buff!!!! :biggrin:  dont you have some weights to lift :biggrin:



You my homie. ;) :biggrin:
 

·
Registered
Joined
·
3,417 Posts
Originally posted by caranto@Aug 30 2005, 10:58 AM~3719917
yes i got an imperial but parker sells a nicer one....hope you got some strong forearms... i had to put mine in a vise to bend some of "poision ivy's" lines....

thanx man im going to parker today, i bent half inch soft copper with my cheap bender and im gonna see if they can match my bends with a hydro bender, if not i may be commin to da ville and payin you a visit lol OR from what ive seen timdog and his for arms, cuz uh..... im 6-2 and 160 and i aint bending this shit at all without sum breaker bars or sumthin lol

OH and thanx again you did a great job on seans caddy that is sweet.........
 

·
Registered
Joined
·
2,562 Posts
Originally posted by eyecandy1n2@Aug 30 2005, 11:22 PM~3724264
thanx man im going to parker today, i bent half inch soft copper with my cheap bender and im gonna see if they can match my bends with a hydro bender, if not i may be commin to da ville and payin you a visit lol OR  from what ive seen timdog and his for arms, cuz uh..... im 6-2 and 160 and i aint bending this shit at all without sum breaker bars or sumthin lol

OH and thanx again you did a great job on seans caddy that is sweet.........
:thumbsup:
 
1 - 20 of 20 Posts
Top