Lowrider Forums banner
1 - 8 of 8 Posts

· Registered
2,014 Posts
Discussion Starter · #1 ·
sup homiez juzt lookin for a stang 83-93 5.0 in good cond. not so worried bout the body but longz the motor iz still runnin strong thx

· Registered
175 Posts
i got a 90 gt not sure if i want to sell it yet maybe for the right money, the body is in good shape no dents no rust its black with black interior, it has 4:10 gears, tremec transmission, stock 302 block it has trickflow heads, upper lower intake, and cam , lots more shit too, the car has ran a 13:24 at 99mph,but it can run better needs custom chip made, its going in the shop next month to have that done, ill post some pics

· Registered
546 Posts
here is mine its a 1990 turbo 5.0 mustang

-Stock ported and polished Heads, new valve seals, crane springs, and milled just a bit to clean it up and seal correctly w/ thicker Felpro Head gaskets
-Edlebrock Performer intake w/ 3/8" spacer and painted black
-New water pump
-160 Degree thermostat
-chrome radiator hoses
-AFCO 2 core 1" cores aluminum radiator
-electric fan
-JAZ catch can
-Powermaster 140 amp alternator
-70mm BBK t/b and spacer w/ EGR delete
-FMS a/c delete
-March underdrive pulleys

-MSD 6BTM w/ remote boost retard and rev limiter
-MSD Coil
-MSD cap and rotor
-FMS blue plug wires
-NGK 1 step colder plugs
-Silcon/fiberglass wire protectors
-Pro-M 3.5" MAF cal. for #42's
-Taylor polished aluminum sealed batter relocation kit in hatch

-Stock t5
-Pro 5.0 shifter
-King Cobra clutch
-Paterson Driveshaft ( Driveshaft shop in Indy)
-FMS 3:55 gears
-Southside lower rear control arms
-Eibach lowering springs
-BBK adj. clutch quadrant
-Power Slot slotted front rotors
-KYB shocks and struts
-Alburn Pro diff.
-Kenny brown sub frames

-255 intank
-Vortech Billet Rails
-Earl's fittings
-Black braided line
-#42 green top injectors

-Presicion PT-61 turbo
-Tial 44mm W/G
-Tial 50mm BOV
-Big Cartech FMIC
-all silicone couplers
-all v-bands and t-bolts
-polished aluminum intercooler to intake piping
-Mac Headers redone and flipped w/ all custom piping and all head coated and wrapped
-all hoses close to heat have silcone/fiberglass wrapping
-Halman manual boost controller

-Autometer shift light
-Autometer 2 5/8" water temp
-Autometer 2 5/8" oil psi
-Autometer 2 5/8" a/c vent plate for gauges above
-Autometer dual piller pod
-Autometer 2 1/16" boost
-Electric 2 1/16" fuel psi
-Greddy turbo timer w/ timer, batter volt, a/f capabilities
-very clean grey interior but missing spring for ash tray

-17x9.5 cobra r's w/ silver rim lip and black spokes
-Kumo 255/40/17 front
-BFG 275/40/17 back

-5% tint
-Cobra rear bumper cover
-GT wing
-4" fiberglass cowl hood w/ hood pins

pm me if interested
1 - 8 of 8 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.